PP calcium carbonate filling masterbatch

February 11, 2011 on 11:52 am | In Products | No Comments

Injection level PP calcium carbonate filling masterbatch, good fluidity and white degree is high, the products can be used for machining luster, PP, PE plastic products,

PP caco3

such as: disposable fast-food, knife, fork, pallets, eat mat, cap, bags, tubes, electrical hull, all kinds of plastic components,

Widely used in injection molding, blow bottle, plastic knife and fork, snack box, tubes, sheet, corrugated board, electrical housing, pack, woven bag, ruddish bags, shopping bags, non-woven, striped cloth, flow delay membrane etc.

recommend add ratio 20% ~ 50%, processing temperature ℃ – 240 ℃ 220

The product has obtained SGS environmental protection attestation

25 kg/bag

Caco3 Filler

November 3, 2010 on 12:06 pm | In Products | No Comments

Caco3-Filler 

Features:

1, the products in the PO, PE film products such as filled with good dispersion and compatibility.
2, a significant reduction in the cost of plastic products, plastic raw materials savings, increase economic efficiency.
3, good plastics, grains, good whiteness, for the milky white film, may be appropriate to reduce the amount of a white mother.
4 Guangyan eliminate products, increasing the film and the opening of shading.
5, non-toxic, tasteless.
Second, the adaptation range for injection molding, extrusion, drawing, PO, PE bags, roll bags, shopping bags, vest bags, garbage bags, rolling film.

processing instructions

1. And a direct mixing of raw materials production, without changing the process.
2. Add 10% to 30% the proportion Note: pay attention to moisture moisture, avoid direct sunlight, at 8 hours after opening for use.
The company’s products to ensure quality, reasonable price, customers are welcome to inquire to buy used.

PPR Masterbatch

November 3, 2010 on 11:45 am | In Products | No Comments

PPR masterbatch is one of my company introduced species, which have the following technical characteristics.

PPR
1, non-toxic
2, high temperature (220 ℃ high temperature for 5 minutes or more does not fade)
3, smaller melt index, the higher molecular weight.
4, the higher the intrinsic viscosity.
5, heat stabilizers. UV WP agent. (200 ℃ oxidation induction time> 60min, UV absorption coefficient ≥ 400)
Thus the formation of the following characteristics:
1, high temperature,
2, no bleeding.
3, the PPR for the matrix material for almost does not affect the physics of the original PPR pipe performance.
4, meet the health requirements, the use of masterbatch in the pipe line with GB/T17219-98 standards.
5, little or no adsorption of the adsorption of chloroform.
6, an outstanding price. Prices much lower than similar imported products, while the performance is very close to or equivalent.
Note: (PPR grade masterbatch Features)
① high concentration, full color, metal sense.
② processing performance, long-term process without removal of material, pipe surface without removal of material, pipe surface without smooth, no scratches.
③ regulation size PPR materials, improved processing performance and reduce processing has generated a quality problem.
Variety: light gray camel, camel gray, white, green, yellow, blue, red stone Hz, iron gray and so on.
Proposed to add the ratio: 1:50 Can be customized according to customer requirements.

Black Masterbatches 2014

September 27, 2010 on 1:27 pm | In Products | No Comments

Black Masterbatches 2014 Cabot selection of imports and import of high concentrations of carbon black melanin new PE material polyethylene resin, and imported paint additives, water-cooled high-energy mixing extruder, air Dice made of carbon black content of 56%.

Appearance

3.0 * 3.2 black flake-shaped vertebral body and 3.0 * 3.3 rounded black body

Adaptation range

Most of the tree for that heat. Injection, pumping tablets, clips and other technology, an environmentally friendly high concentration, injection molding grade high-luminosity black masterbatch, the product of heavy metals through the EU SGS environmental protection test certified eight items.

Advantages

Environmental protection, non-toxic, odorless, smokeless, surface smooth and glossy and the color stability of solid color, will not color point and color patterns such phenomena, not only reduce costs, saving additives, reducing factory space pollution.

Usage

Production and raw materials can be mixed evenly.

Usage

Recommended dosage of 1% -3% (depending on the product requirements).

Technical parameters

Bulk density: 25 “C 1750kg/m3
Melting point: 130-250′C
Solution that: 40g/10min
Water: 0.02%

Package

25KG / bag, polyethylene bag or milky white printing paper and plastic bag (to be made according to customer demand).

Storage

Store in a cool dry place, avoid prolonged sun exposure, rain.

Remarks

The above data are not provided for the use of specific technologies, the basic test shall prevail.

Plastic Masterbatches Water Absorber Masterbatch

October 16, 2008 on 11:33 am | In Products | No Comments

Features Specifications: Water Absorber Masterbatch

PRODUCTDESCRIPTION

EPA 301 is an advanced functional masterbatch specially developed to solve moisture problem. It can dramatically absorb moisture from PE / PP resin during processing.

FEATURES

EPA 301 brings no negative effect to product physical and mechanical properties. The production cost can be reduced and productivity is increased accordingly as no material pre-drying is required.

APPLICATIONS

It can be applied to absorb moisture in the process of film blowing,injection molding, blow molding, profile extrusion, etc. with PE / PP as the carrier.Typical addition rate is 1 ~ 3%. Actual addition rate may vary depending on moisture level.

PHYSICALPROPERTIES

Appearance: Gray (pellet)

Density: 1.5 ± 0.3 g/cm3
Volatile content: < 0.5%
Melt Flow Index: 0.1 - 10.0 g/10mins
Absorptivity: > 13%
PACKAGING ANDSTORAGE

20 kg per box with4 x 5 kg inner polybag vacuum packing. Product should be kept in dry, cool,clean place with good ventilation, away from sunlight and rain. Always heat-seal inner polybag immediately after unpacking.

SHELF LIFE

The shelf lifeof EPA 301 is 8 hours after exposure to open air. After PE / PP pellets are mixed with EPA 301, start massive production as soon as possible.

Scent polyolefin masterbatch

October 2, 2008 on 10:29 pm | In Products | No Comments

1. Introduction
Polyolefin masterbatch fragrance is a given polyolefin (PE, PP, etc.) a certain fragrance materials functional masterbatch.

2. the performance characteristics of
1, good temperature
In the normal plastic processing temperatures, used in the evaporation loss perfume and flavor of its role in the destruction of the structure is not clear
2, lasting fragrance

Due to fully consider the essence of the ingredients of sustained-release request, in the formula used in a wide range of help to control the release of the flavor components, and
In the masterbatch in the preparation for a special process.
Usually the polyolefin masterbatch can smell the six months to two years to maintain.

3:the use of

Usage: 1 to 4% (can also be manufactured in accordance with the specific requirements of choice) will be the ratio of masterbatch resin mixed with the raw materials can be used after the uniform.

4:IV Notes
1, with good material should be used as soon as possible, not parking too long.
2, the mother is expected to open as soon as possible after the use of packaging.
3, the packaging not use up all the time after the mother is expected to be fully sealed and packaged.

Flame-retardant masterbatch

October 2, 2008 on 10:17 pm | In Products | No Comments

I. Introduction:
High-performance flame-retardant masterbatch selection of high-performance series of flame retardants, the unique preparation, not only with reliable fire-retardant, and has good
Good dispersion and resin matrix of compatibility for ABS, HIPS resin.

II, the major technical indicators:
Project: Technical indicators
Appearance: uniform particles
Flame retardant: V-0, V-1, V-2, HB-class
Migration of resistance: ≥ 4 level

III, the use of ratio and methods:
Flame-retardant materials will be home to 1:3-1:4-1:5 resin and raw materials (in accordance with the requirements and fire-retardant resin species may be) evenly mixed, some of the dried product.

Fill transparent masterbatch

September 30, 2008 on 10:25 pm | In Products | No Comments

1, the product profile
Transparent masterbatch filled with ordinary filling masterbatch, the biggest feature is added to the PP, PE, transparent to its impact on small, can be widely used in the film, sheet, tubing, containers and other areas. If the use of PE films, the right to add volume to improve the transparency of HDPE film, LDPE film transparency almost no impact.

At the same time have a very good surface finish and balanced mechanical properties. These are commonly available to fill the masterbatch unmatched. It can be predicted, the mother of filling materials, plastic will fill the lower reaches and its application in the field have a greater impact.

2, the product features:
(1) transparency, and add the amount of light transmission rate is still 30 to reach 90%
(2) on the mechanical properties of the loss is very small, basically to keep the main mechanical properties of materials
(3) do not change the original equipment, technology
(4) to reduce product costs 5-10% or more (based on the need to add a specific amount of calculation)

3, the use of methods:
This Masterbatch and plastic raw materials directly mixed evenly, you can carry out production and processing. General recommended adding amount of 5% to 30%, according to the specific requirements of the right to choose the proportion of added.

4, storage conditions:
Ventilation in the clean, dry, cool, clean place to preserve. Masterbatch does not allow damaged packaging and store exposure and avoid sun exposure, and the rain.

5, shelf-life:
Production from the date of 1 year.

Calcium carbonate masterbatch filled with PP carrier

September 30, 2008 on 10:09 pm | In Products | 2 Comments

Calcium carbonate filler material from the mother of the last century since the birth of the early 1980s, for plastic processing industry and society as a whole has made great contributions to the annual output reached more than 1,000,000 tons, is a modified plastic one of the important species.

masterbatch.jpg” />

Masterbatch fill the first carrier to use the polymer when the PP is a by-product – random polypropylene (APP), hence known as APP masterbatch. After the Beijing Yanshan Petrochemical Corporation as a result of technological transformation, no depletion of the source of polypropylene, synthetic resin and calcium carbonate as a substitute during the shortage, the market demand. In this context, in order to polyethylene resin as the carrier of calcium carbonate-filled masterbatch came into being, such as LDPE1F7B is still the mother is expected to fill most of the major raw materials.

As the mother of filling materials are mainly used for stretching the use of polypropylene bags and packing tape, from the price, compatibility and strength in areas such as stretching, the use of polypropylene resin as the carrier filled more suitable for such a masterbatch.

The early 1990s, the then Ministry of Light Industry Institute of Plastics Processing application to be the first to introduce polypropylene powder as the carrier resin material calcium carbonate-filled mother, known as the PPM masterbatch, and in 1992 won the State New product class title.

PPM masterbatch small body PP powder as a carrier compared to price, such as PE resin 1F7B a significant advantage, so far has kept 1,000 yuan / ton over the price difference. At the same time, the low density of the PP in itself means that the same quality of the resin more of the number of vector borne polymer resin.

In addition the strength of PP is higher than PE, under the same conditions allow stretching, packaged with a higher intensity, such as different carrier made of resin-filled PP masterbatch for injection molding products, and will be stretching, packaged with Similar products such as the results of the PP as the carrier is about to fill the resin masterbatch with other resins for the carrier to fill the masterbatch, according to the QB 1126-91 “filled polyolefin masterbatch” industry standard spline made of injection, When the same formula, sample preparation equipment, conditions at the same time, PP as the carrier filled the masterbatch best.

The PP as the carrier filled with calcium carbonate masterbatch production of the main points are as follows:
① PP granular powder PP than cheaper, more evenly mixed with calcium carbonate, priority should be to use.
② powder melt flow rate of the PP not be too big, 4 ~ 10g/10min for good.
③ PP powder did not join the antioxidant, lubricant additives, and so on, we must add the appropriate amount.
④ PP powder stored in the process of gradual degradation, let sour, it must be time to ask the production and use in a timely manner, preferably in a polymer used up within one month after.
⑤ to PP powder as the carrier of calcium carbonate-filled masterbatch can use the same parallel to the twin-screw extruder processing, the ratio of calcium carbonate can reach more than 80%. The key question is not eager Granulation air-cooled surface model, we should not be using the pull water granulation, the only way to use air-cooled grain belt.
1.2.2 for ABS in place of the main goals of the modified Polypropylene

(1) Co., Ltd. of Japan Karp CALP resin composition, performance and purpose
CALP resin on many occasions can be expensive to replace the ABS, there are still obvious shortcomings.

  1. Than the density of large ABS;
  2. Low surface hardness, described intolerance;
  3. Less rigid;
  4. Low-gloss surface;
  5. Poor surface coating;
  6. Forming large size shrinkage. The original use of ABS injection molding die need to be modified to use modified PP resin.

Master batch

September 26, 2008 on 6:21 pm | In Products | No Comments

The use of masrerbatch has dominated the market ,it is obvious that to dye and change the nature of the plastic material with the masterbatch is quite a potential market and a certain trendency . To meet this demand ,

our company have apecially set up the research and production department of masterbatch to assure precise color matching by computer operation and advanced testing system and first class producing line .

Entries and comments feeds. Valid XHTML and CSS. ^Top^